How Can You Effectively Monitor Your Blood Sugar at Home?

  1. Code the meter to match or calibrate the meter to reactivity of the Test Strip by following the manufacturer’s instructions and matching a number on the meter’s display to a number on the Code Strip or on the test strip package.
  2. Wash your hands vigorously with soap and warm water. Rinse and dry thoroughly with a paper towel.
  3. Remove the Test Strip from the package.
  4. With the meter off, insert the correct end of the test strip into the test slot of the meter, according to the manufacturer’s instructions. This usually turns the meter on.
  5. Remove the end cap from the lancing device.
  6. Insert a short lancet into the lancet holder according to the manufacturer’s instructions. Twist off the protective cap and save it for the disposal of the used lancet.
  7. Replace the end cap. The depth of the puncture depends on the end cap used.
  8. Re-cock the lancing device.
  9. Choose your puncture site. The sides of the end segment of the finger are the best sites. Stroke down the finger to push blood toward the puncture site.
  10. Place the end cap firmly against the chosen puncture site on the side of the fingertip. The more pressure you use, the deeper the puncture. Push the lancet release button without moving your finger or the device.
  11. After the puncture, remove the lancing device. If a drop of blood does not form on its own, stroke down the finger toward the puncture site without going as far as the site itself.
  12. Hold the tip of the test strip in the drop of blood until the meter tells you the test strip is filled, usually by beeping. Remove the test strip from the blood. Put the device and the strip aside until the reading is complete.
  13. Wipe the puncture site with clean, dry facial tissue and use the tissue to hold pressure on the puncture site until the bleeding stops.
  14. Remove the end cap from the lancing device and remove the used lancet.
  15. Replace the used lancet back into the protective cap by pushing it into the open end of the cap, which is placed on a firm, flat surface like a countertop.
  16. Once the blood sugar reading on the meter is complete, use the tissue to grasp the test strip and pull it out of the meter. This usually turns the meter off.
  17. Discard the lancet in its protective cover, and the used strip into a glass or puncture-proof container with a screw top or a “Sharps” Container purchased from your local pharmacy. Replace the cap on the container. When the container is full, cap it and discard it into the trash.
  18. Clean the lancing device weekly according to the manufacturer’s instructions.
  19. Only use a lancet once.
  20. Do not use the same end-cap on another person.
  21. Teach another person to use the whole system so that you have a backup when you need assistance.

Monitoring and tightly controlling your blood sugar level can significantly reduce the risk of complications due to diabetes and provide you with a higher quality of life.

Knowledge of your blood sugar levels at different times of the day is an essential input into your diabetes care plan and allows you and your medical team to work out and modify your plan for medication, diet, and exercise.

The heart of the system to monitor your blood sugar is the blood glucose meter and the automatic lancing device used to obtain your blood sample.

There are many types of glucose meters with varying degrees of sophistication and abilities to store test results. Your doctor or nurse will recommend the type best for you.

You will need to be familiar with the manufacturer’s instructions for each unit. This program will provide you with general guidelines that apply to all units.

The equipment you will need to assemble includes:

  • the glucose testing meter,
  • a packet of test strips,
  • an automatic lancing device,
  • and facial tissue, alcohol wipes.

The meter will have a display with blood sugar readings are shown, an on/off power button, and a slot into which the Test Strips are inserted. In the back of the meter will be a compartment for batteries.

The Automatic Lancing Device has three components: the body with a release button, lancet holder and cocking device, the removable end cap, and a separate short lancet.

The first step is to code the meter to match or calibrate the meter to the reactivity of the Test Strip.

This is done by following the manufacturer’s instructions and matching a number on the meter’s display to a number on the Code Strip or on the test strip package.

Coding is done:

  • Whenever a new package of Test Strips is opened  (Note: not all meters need manual coding).
  • Daily to ensure the meter is coded correctly. (verified daily or with each use).

In addition, a control test can be run if you need to check that the whole system of the meter and the test strip is working correctly and to practice your good meter techniques.

Follow the manufacturer’s instructions, which usually involves testing a control solution of sugar that is provided with the meter.

Wash your hands vigorously with soap and warm water. Rinse and dry thoroughly with a paper towel.

Remove the Test Strip from package.

With the meter off, insert the correct end of the test strip into the test slot of the meter, according to the manufacturer’s instructions. This usually turns the meter on.

Remove the end-cap from the lancing device.

Insert a short lancet into the lancet holder according to the manufacturer’s instructions. Twist off the protective cap and save it for the disposal of the used lancet.

Replace the end-cap. The depth of the puncture depends on the end-cap used.

Re-cock the lancing device.

Choose your puncture site. The sides of the end segment of the finger are the best sites. Stroke down the finger to push blood toward the puncture site.

Place the end-cap firmly against the chosen puncture site on the side of the fingertip. The more pressure you use, the deeper the puncture. Push the lancet release button without moving your finger or the device.

After the puncture, remove the lancing device. If a drop of blood does not form on its own, stroke down the finger toward the puncture site without going as far as the site itself.

Hold the tip of the test strip in the drop of blood until the meter tells you the test strip is filled, usually by beeping. Remove the test strip from the blood. Put the device and the strip aside until the reading is complete.

Wipe the puncture site with a clean, dry facial tissue and use the tissue to hold pressure on the puncture site until the bleeding stops.

Remove the end-cap from the lancing device and remove the used lancet.

Replace the used lancet back into the protective cap by pushing it into the open end of the cap which is placed on a firm, flat surface like a countertop.

Once the blood sugar reading on the meter is complete, use the tissue to grasp the test strip and pull it out of the meter. This usually turns the meter off.

Discard the lancet in its protective cover and the used strip into a glass or puncture-proof container with a screw top or a “Sharps” Container purchased from your local pharmacy. Replace the cap on the container. When the container is full, cap it and discard it into the trash.

Clean the lancing device weekly according to the manufacturer’s instructions.

Only use a lancet once.

Do not use the same end-cap on another person.

Teach another person to use the whole system so that you have a backup when you need assistance. 

This video is intended as a tool to help you to better understand the procedure that you are scheduled to have or are considering. It is not intended to replace any discussion, decision making or advice of your physician.